CatK ReDefine Design
  • Home
  • Create
    • The Entire Blog-chilada
    • Project Index >
      • Tree Branch Chandelier
      • Roll Up Dog Bed/Picnic Blanket
      • Dog Furniture
      • Pendant Lights
      • Industrial Shelves
      • Folding Dining Table
      • Around The House
      • Christmas Creativity
      • Murphy Headboard
      • Ombre Curtains
      • Fainting Couch
      • Piano Bench
      • Wingback
      • Decorative Dog Crate
      • Mason Jar Chandelier
  • Plate
  • Renovate
  • About

Decorative Dog Bed

1/10/2015

0 Comments

 
Decorative Dog Furniture Bed
I wanted to post an old project of mine. Sorry for the limited pictures! I wanted to make a more asthetically pleasing bed for my dog, and I also wanted to direct him to something other than the sofa. He liked being high enough to look around the room and see out the window so this was my solution!

Materials

  • 3'x3' foam, 4" deep
  • 3'x3' 1" thick plywood
  • 1x6" lumber cut into (2) 37.5" lengths and (3) 36" lengths
  • Four Legs and appropriate fasteners for these

  • Staple Gun
  • Nail Gun
  • Fabric
  • Batting

Steps

  1. Mark two inches from the bottom on the four pieces of 1x6 lumber
  2. Use the 1x6's to form a box around the plywood square, nailing the plywood at the 2" line you drew. 
  3. Put the two 36" boards on opposite sides and then the 37.5" boards on the remaining two sides, nailing all the corners together
  4. Attach the legs to the bottom corners of the plywood square
  5. Now the frame is complete!
Dog Bed Frame
Dog Bed Frame
  1. For the upholstered portion first wrap the 1x6's in batting and secure in place with staples
  2. Take a long strip of fabric and wrap it around the outside of the frame and then  fold the fabric over the top of the frame and staple it on the inside.
  3. Then, turning the entire project over stretch the fabric to the underside and staple it there
  4. Finally, I was lazy and just wrapped the fabric around my cushion and safety pinned it in place. Then squashed the pillow into the frame.
Dog Furniture
0 Comments

Folding Dining Table

12/28/2014

0 Comments

 
Folding Dining Table
Our house doesn’t have a dedicated dining room- or even a breakfast room- and since we love to entertain this has been a bit of a problem. We have a good sized sectional so I wanted to be able to use that for seating like a banquette, but we have a large, heavy coffee table that isn’t practical to move regularly. Finally we settled on making a folding dining table that could sit over the coffee table. Here’s how we made it:

Materials

  • Sturdy Square folding table
  • ¾” thick ply wood, pre-cut to 4’x6’
  • Drill
  • Saw
  • Matching veneer edging
  • Stain
  • Spray Polyurethane

Steps

  • Start with a sturdy folding table with a metal or wood frame and a wooden top (we got ours from Target). We had to use the old school square kind (like the card table your grandmother has!). This was a requirement because we needed the legs to sit on the sides of the coffee table and not the Y bar that the rectangular tables use.
Folding Dining Table
  • Standard dining chairs are taller than a sofa so sit on your sofa and measure from the floor to your ideal table height. Save the rubber feet from the metal legs and then cut the legs to give you the right table height. Reattach the feet on the cut legs.
  • Cut the corners off the plywood tabletop (this is so people can move around the table easier since they are sitting on a sofa) and sand all the edges down, rounding the points.
  • With the bottom of the plywood up, measure and place the folding table in the center of the plywood. Then use multiple the screws to firmly attach the folding table to the new plywood table top.

  • Attach veneer edging and stain wood desired color and complete with spray on Polyurethane

It is now complete! If you are in a loft you could also attach mounting toward the top of the plywood and hang it on the wall as is or get creative and paint it to use as art!

Loft Dining Table
0 Comments

Industrial Shelves

12/27/2014

6 Comments

 
Rustic Industrial Shelves
I spent a while looking at different shelving ideas and finally settled on exactly what I wanted, I nice, rustic/industrial floating shelving unit. Here is the sketch of my "vision"
Industrial Shelves
I wanted a nice rustic shelf so we went with 2” thick building grade lumber and a hanging rail system to attach it to the wall

I was only able to get the rail system in a mixture of black and white, but I wanted everything a rubbed bronze color so spray painted all the railing
Painting Shelving Frame
Shelving Frame installed
Then we attached the railing system to the studs and painted the “cubby” my teal accent color


Next we sanded and cut all the shelves to size. Then notched the shelves where the rail bars would go so the shelves would sit flush against the wall
Staining Shelf wood
Rustic Shelves
Picture
Treated the pine with Minwax Pre-Stain (which is a requirement to get pine to stain well)

Then stained everything and finished it off with a satin spray on Polyurethane

Rustic Shelves
Industrial Shelves
Finally, we assembled and filled with goodies. The shelving is complete!


Rustic Shelves
6 Comments

Shelving Decisions!

12/11/2014

1 Comment

 
Shelving Decisions! 12/11/2014

0 Comments


 
I really want to get shelving squared away in my living room. I have so many nick-nacks and mischellani that I want to have out. Not to mention those are the things that add character and warmth to a home. So I have been scoping things out for a little while and am starting to get a good idea of what I want them to look at. Here are some of my inspirations! 
Follow CatK's board Industrial Living Room Shelving on Pinterest.
1 Comment

Upholstered Murphy Bed Headboard

12/11/2014

6 Comments

 
DIY Murphy Bed Headboard button nailhead
We love having guests come stay, and in our new place there wasn’t enough room for a dedicated guest room, so we decided to make my husband’s office a multi-use space by adding a Murphy bed. We found a used Murphy bed frame on Craigslist and got that installed but the when the bed is down (in “bed” position) there is a huge gap between the head of the bed and the wall since the bed pivots. I knew I wanted to have some type of headboard but it couldn’t be anything permanently attached, it would have to move with the bed as it opened and closed. It took a while mulling over the problem before I finally came up with the solution. 

I could create a two part headboard. The headboard Base would be sandwiched between the head of the bed and the metal frame that kept the mattress from sliding off the frame. This would have hinges used to attach the main portion of the headboard, which would fold over the bed when it was in it’s upright position and then flip back to lean against the wall to form the headboard when it is in use. *see design drawings below*
Here are the pictures of the Murphy Bed folded up and laid down before the headboard

Materials

  • Plywood pre-cut at Home Depot to ­­­57” x 37” (Headboard) and 57” x 9.5” (Base) dimensions (*width must not exceed width of bed or the Murphy Bed will not fold up so if you are making this PLEASE measure your specific Murphy Bed)
  • Twin bed quilt batting 
  • Staple gun and ¼” staples
  • Four door hinges
  • Drill
  • Button making kit
  • Decorative nail head trim
  • Long upholstery needles
  • Cable Ties
  • Heavy duty thread or button floss

Steps

I was going to use cable ties to attach the support board to the metal frame, so first off I placed that at the foot of the bed and marked where the wholes would need to go for the cable ties and drilled those holes.

Line both boards up with and attach hinges evenly spaced, then remove the pins in the hinges so they boards are again separate

I want button tufting so measured on my fabric where I wanted those to go and then marked where I wanted the buttons on the board, then drilled holes for those.

Murphy Bed Headboard
Take the quilt batting and using it in a double layer, stretch it across the main headboard and staple it down on the back. Cut v-shaped spaces for the hinges as you are going and make sure the batting will not interfere with the hinges
Cut the bottom layer of batting even with the hinges and tuck the top V under the bottom layer so it lays just against the hinge
I used long needles sticking through the button holes I pre-drilled to make sure that the fabric lined up correctly with my buttons. With these in place I carefully stretched the fabric and stapled it to the back of the board.

I used the same trick for the hinges from earlier and cut V’s and tucked those under the batting
DIY headboard buttons
There is a heavy duty button floss you can use for attaching your buttons, but I didn’t have it do just used three strands of heavy duty thread. Cut this very long, string your button so it is dangling in the middle of the thread and then carefully poke your needle through the fabric in the spot you want your button to sit. 

Pull the thread through the drilled hole to the other side of the headboard and separate the two halves of the thread. Take some of the quilt batting and form it into a fluffy “meatball” and place that between the ends of thread. Now make a slip knot out of the two ends of thread and pull it on the batting until the button looks like you want. Once it is in place do several tight knots to permanently tie your slip knot in place.
Button Tufting
For the nail head trim, I decided to cheat a little and use the string of nail heads where you only have to attach every 5th one; this is a lot faster and a lot easier to keep straight

  • There are special decorative tack hammers with silicone ends that won’t damage the tacks but I didn’t have one so I took some wadded up fabric and taped it to the end of my hammer
Picture
Using a T-Square for simplicity sake I used it’s width as a guide and traced the line with a pencil, and then I attached my nail head trim making sure to stay on the line.
Headboard Nailhead Trim
The last step on the headboard was to stretch some scrap fabric over the entire back and staple that in place. It gives it a clean, finished look when it is down and will help to keep the batting balls holding the buttons in place from coming loose.

I wanted consistency to on the base I strung my zip ties through, then followed the same process I used above; Covered it in batting, then fabric.

I positioned the base exactly where I wanted it, and then used the zip ties to secure it to the frame. Once that was attached I lined the headboard hinges up and put the pins back in. Gravity would keep the headboard in place just fine but for a little extra insurance I added Velcro strips to the top edge of the headboard and the wall.
Button Tufted Nailhead headboard
Button Tufting
Nailhead Trim

Update: 10.25.15

I have had a couple of questions on how this was attached so took a few more pircutres and took a quick video to try to better show the hing and how I attached the headboard to the frame

Video:


Base:
​For the "base" portion of the headboard I had drilled holes in the wood for cable ties where they would loop over the metal frame and ran the ties through the holes before i covered it with fabric.
Picture
This is the best picture of the metal frame at the head of the bed from before I installed the headboard:
Picture

​Headboard from the front:
Picture
With mattress pulled out
Picture

Images of the space between the wall and back of the headboard
- Since no one sees this I didn't bother to make it pretty, it's just functional :)
Picture
Picture
Picture
Front to Back View
Picture
Picture
Picture
6 Comments

Piano Bench in a Pinch

8/13/2014

1 Comment

 
Reupholstered Piano Bench
One of my favorite hobbies is playing piano; it is something I have been doing since I was 6 years old. I have the standard "padded" piano bench that came with my piano when I bought it was few years ago. Basically it is a boring black vinyl seat, and the "padded" part is really just a joke to tease you into sitting down too fast and busting your bum on the solid wood under the tiny layer of what I am convinced is quilt batting. The piano is in my office space which I mostly have decorated in pretty blues/teals with some pink accents.

So I decided that it needed a refresh! This isn't a full "quality re-upholstery" job, I left all the original pleather and padding and was careful not to damage them in case at some point I want to go back to the "standard look." 

Supplies

  • Piano bench
  • 1" foam (from the fabric store)
  • Upholstery fabric
  • Staple Gun
  • Sharpie Marker or similar
  • Staples (3/4" is fine)
  • Phillips Head Screw Driver
  • Flat Head Screw Driver
  • Pliers

Picture

Steps

  1. Remove screws securing padded portion to bench (save these)
  2. Pry padded portion off of bench frame (this took some work on mine as there was also glue)
  3. Lay the old padded portion over the new foam and on the foam draw around the bench
  4. Cut foam to appropriate size and bevel edges slightly
  5. Lay fabric, print side down, on the floor, then center the foam and set the original padded piece on top of it so the wood is showing
  6. Starting in the center, stretch and staple the fabric over the bench until you have a look you like, taking care to tuck the corners 
  7. When the fabric is secured and stretched how you want it, screw the updated piece back onto the bench frame and admire your work!

DIY Piano Bench
1 Comment

Fly Little Wingback!

7/27/2014

0 Comments

 
Picture
I have a family heirloom wingback chair that I have been thinking about reupholstering for a while, and finally signed up for a class to go through the process. After a lot of concerns were raised by the rest of my family at me trying to tackle that particular chair, I search Craigslist and managed to find this little beauty to try my hand at first.

I enrolled in a 6 week class here in Austin at Austin Upholstery Studio. I am trying to dig up the progress pictures but those were all on my old phone and I can't find it for anything! I will keep searching but in the meantime, here are before and after pictures. 

I went with a texture rich, slubbed grey velvet for the front facing, and then this really cool fabric that is reminiscent of the colors and texture of burlap (but a more fine linen look weave) with a silver design stamped directly on it. Finally I finished the chair off with large format, rustic silver nail head trim.

After

Picture

Before

Picture

Picture
Picture

Picture
Picture

Picture

Picture
0 Comments

    Author

    I love beautifying my home, including renovations, projects, and handy tips to make life a little easier
    ~ CatK

    RSS Feed

    Subscribe to get updates directly to your inbox! Enter your email address here:

    Delivered by FeedBurner

    Categories

    All
    Around The House
    Christmas
    Curtains
    Designer Dog
    Fainting Couch
    Furniture
    Home Decor
    Industrial
    Industrial Shelves
    Lighting
    Murphy Bed
    Ombre
    Plate
    Restaurant Review
    Rustic
    Shelving
    Small Smart Spaces
    Upholstery

Picture
Tree Branch ChandelierThe Bling Branch - Tree Branch Crystal Chandelier
11/20/2015
We have spent most of the past few months working on our deck, but it is finally finished and now it is time
...

Picture
Pendant LightsQuick and Painless Pendant Light Update
1/19/2015
Our house came with the standard builder grade pendant lights (see picture below)...

Picture
Roll Up Dog Bed/Picnic BlanketRoll up Picnic Blanket or Dog Bed
4/18/2015
Austin is a wonderful, pet friendly town and I love to take my dog out on pretty days, but I have to...

Picture
Dog FurnitureDecorative Dog Bed
1/10/2015
I wanted to post an old project of mine. Sorry for the limited pictures! I wanted to make a more asthetically pleasing...


© COPYRIGHT 2015. ALL RIGHTS RESERVED.